routeros-mndp

MNDP — MikroTik Neighbor Discovery Protocol

MNDP is the UDP broadcast/multicast protocol that RouterOS uses for automatic device discovery on the local network. It is the same protocol WinBox uses to find routers. Every RouterOS device participates by default.

Why This Matters for Agents

• /ip/neighbor on RouterOS is the CLI/REST surface for MNDP results
• WinBox's "Neighbors" tab is an MNDP listener
• Any agent implementing device discovery for MikroTik equipment needs MNDP
• The protocol is simple enough to implement from scratch — no library needed

Protocol Basics

| Property | Value | |----------|-------| | Transport | UDP | | Port | 5678 | | IPv4 | Broadcast to 255.255.255.255:5678 | | IPv6 | Multicast to ff02::1 (all-nodes link-local) | | Direction | Bidirectional — same port for send and receive | | Authentication | None — read-only discovery, no credentials | | Scope | Layer 2 broadcast domain (does not cross routers) |

How Discovery Works

1. Listener sends a refresh packet — a small UDP datagram to 255.255.255.255:5678 (MAC-Telnet sends a minimal 4-byte zeroed header; a 9-byte form also works — see below)
2. All RouterOS devices on the LAN reply — each sends a TLV-encoded announcement with identity, version, board, MAC, IP, uptime, etc.
3. Replies arrive asynchronously — devices respond within milliseconds to seconds depending on network conditions
4. RouterOS devices also announce periodically (~60s cycle) without being prompted — passive listening works but is slow to populate

Refresh Packet (Discovery Request)

A short packet that triggers immediate replies from all RouterOS devices on the broadcast domain. The minimal form is just a zeroed 4-byte header — this is exactly what MAC-Telnet sends (unsigned int message = 0;):

Offset  Length  Value       Field
0       1       0x00        header byte 0 (version per MAC-Telnet; "unknown" per Wireshark)
1       1       0x00        header byte 1 (ttl per MAC-Telnet)
2       2       0x0000      seqno / checksum

As raw bytes (minimal): 00 00 00 00

Some implementations append an explicit refresh TLV (type 6, length 0). The complete header + empty-TLV form is 8 bytes (00 00 00 00 00 06 00 00); some implementations add a trailing zero byte (non-semantic padding), giving 9 bytes. RouterOS accepts all forms:

Offset  Length  Value       Field
0       4       00 00 00 00 header (2 header bytes + 2-byte seqno)
4       2       0x0006      TLV type = 6 (refresh)   ← big-endian
6       2       0x0000      TLV length = 0
8       1       0x00        optional trailing pad (non-semantic)

As raw bytes (9-byte form): 00 00 00 00 00 06 00 00 00

Response Packet

Offset  Length  Field
0       2       header bytes (version + ttl per MAC-Telnet; "unknown" per Wireshark)
2       2       sequence number (big-endian; per-device counter)
4+      TLV[]   zero or more TLV records (see below)

The first 4 bytes are a fixed header; parsers skip the first 2 bytes and read the sequence number as a big-endian uint16, then iterate TLVs from offset 4.

TLV Format

Each TLV (Type-Length-Value) record in the response:

Offset  Length  Field
0       2       type   (big-endian uint16)
2       2       length (big-endian uint16) — byte count of value
4       N       value  (raw bytes — interpretation depends on type)

Byte order: TLV type and length are big-endian (network byte order — ntohs). This is confirmed by the canonical reference implementations: MAC-Telnet's protocol.c (type = ntohs(type); len = ntohs(len);) and the official Wireshark MNDP dissector (packet-mndp.c, which reads both with ENC_BIG_ENDIAN).

Value encoding varies by type and is the most common footgun: string TLVs are UTF-8, IPv4/IPv6/MAC are raw network-order bytes, but TLV 10 (uptime) is a little-endian uint32 — the only little-endian value in the entire protocol. Everything else multi-byte is big-endian/raw.

TLV Type Reference

| Type | Hex | Name | Value Format | Notes | |------|--------|----------------|-------------|-------| | 1 | 0x0001 | MAC Address | 6 raw bytes (network order) | Per-interface MAC, not chassis MAC | | 5 | 0x0005 | Identity | UTF-8 string | Hostname — same across all interfaces | | 7 | 0x0007 | Version | UTF-8 string | e.g. 7.18 (stable), 7.22rc1 | | 8 | 0x0008 | Platform | UTF-8 string | Usually MikroTik | | 10 | 0x000a | Uptime | 4 bytes LE uint32 | Seconds since boot — the only little-endian value | | 11 | 0x000b | Software ID | UTF-8 string | License identifier | | 12 | 0x000c | Board | UTF-8 string | e.g. RB4011iGS+5HacQ2HnD, CHR | | 14 | 0x000e | Unpack | 1 byte | Firmware compression flag (some parsers treat as IPv6-present flag) | | 15 | 0x000f | IPv6 Address | 16 raw bytes | Link-local or global IPv6 | | 16 | 0x0010 | Interface Name | UTF-8 string | Sending interface on the router (e.g. ether1) | | 17 | 0x0011 | IPv4 Address | 4 raw bytes (network order) | IP of the sending interface |

Source of truth: these type IDs match the canonical MAC-Telnet protocol.c (MT_MNDPTYPE_* enum) and the Wireshark MNDP dissector value table exactly. Note in particular that uptime is type 10, software-id is type 11, and board is type 12 — a common mistake is to off-by-one these (uptime=11/board=13), which silently misparses real RouterOS packets.

Packing TLVs (types 2, 3, 9): related to /ip packing/compression. Safe to skip.

Multi-Interface Behavior

A RouterOS device with N active interfaces sends N separate MNDP announcements — one per interface. Each announcement has:

• A different MAC address (the interface's own MAC)
• A different interface name (TLV 16)
• A different IP address (if assigned)
• The same identity (hostname)

This is expected behavior, not a bug. When displaying results, group by identity to avoid showing the same router N times. Use MAC address to disambiguate when the identity is the factory default (MikroTik).

Timing and Reliability

| Scenario | Expected Response Time | |----------|----------------------| | Local LAN (wired) | 1-3 seconds | | WiFi / congested network | 3-10 seconds | | ZeroTier / tunnel overlay | 5-20 seconds | | Satellite / high-latency | 10-30 seconds |

Best practice: Send multiple refresh packets during the listen window (every 5 seconds, matching WinBox behavior). Devices that miss the first broadcast due to packet loss, WiFi power-save, or tunnel relay latency will respond to subsequent refreshes.

Never interpret missing devices as offline. A short scan window produces partial results. Increase the timeout before concluding a device is unreachable.

RouterOS /ip/neighbor

/ip/neighbor is the RouterOS-side view of MNDP (and CDP/LLDP) discovery results. It shows what the router has heard from other devices on its directly-connected networks.

# Print discovered neighbors
/ip/neighbor/print

# Columns: interface, address, mac-address, identity, platform, version, board

/ip/neighbor/discovery-settings

Controls which interfaces participate in neighbor discovery:

# Show current discovery settings
/ip/neighbor/discovery-settings/print

# Disable MNDP on a specific interface (security hardening)
/interface/list/member/add list=no-mndp interface=ether1
/ip/neighbor/discovery-settings/set discover-interface-list=!no-mndp

# Supported protocols (can be combined)
# cdp — Cisco Discovery Protocol
# lldp — Link Layer Discovery Protocol
# mndp — MikroTik Neighbor Discovery Protocol
/ip/neighbor/discovery-settings/set protocol=mndp,lldp

REST API Access

# List neighbors via REST
curl -u admin: http://<router-ip>/rest/ip/neighbor

# Response is JSON array with the same fields as CLI print

Security Considerations

• MNDP has no authentication — any device on the broadcast domain can discover routers
• Disable MNDP on untrusted interfaces (public-facing, guest networks)
• RouterOS defaults to discovery on all interfaces — review and restrict
• MNDP reveals: identity (hostname), version, board model, IPs, MACs, uptime
• This information is useful for attackers — treat MNDP like an open SNMP community

Socket Implementation Notes

Port Sharing (SO_REUSEPORT)

MNDP uses the same port (5678) for both sending and receiving. If another process (e.g., WinBox) already has UDP/5678 bound, your listener needs SO_REUSEPORT to coexist:

// Node.js / Bun dgram
import { createSocket } from "node:dgram";
const sock = createSocket({ type: "udp4", reuseAddr: true, reusePort: true });
sock.bind(5678, "0.0.0.0", () => {
  sock.setBroadcast(true);
});

// C / POSIX
int opt = 1;
setsockopt(fd, SOL_SOCKET, SO_REUSEPORT, &opt, sizeof(opt));
setsockopt(fd, SOL_SOCKET, SO_REUSEADDR, &opt, sizeof(opt));
setsockopt(fd, SOL_SOCKET, SO_BROADCAST, &opt, sizeof(opt));

Platform note: SO_REUSEPORT works on macOS and Linux. On Windows, SO_REUSEADDR alone may be sufficient. In Bun, reusePort: true requires Bun >= 1.3.11 (earlier versions silently ignored it on macOS).

Self-Echo Filtering

When you send a broadcast to 255.255.255.255:5678, the OS delivers a copy back to your own socket. Filter out packets from your own IP addresses to avoid processing your own refresh as a neighbor response. The looped-back packet will have no MNDP TLVs (it's your 9-byte refresh, not a device announcement).

IPv6 Multicast

IPv6 MNDP uses ff02::1 (all-nodes multicast). Less commonly used than IPv4 broadcast but supported:

sock.addMembership("ff02::1");

IPv6 link-local addresses include a zone ID (e.g., fe80::1%en0) that identifies the receiving interface — useful topology information not available in IPv4.

Parsing Example (TypeScript)

function parseMndpResponse(buf: Buffer): Record<string, string | number> {
  let offset = 4; // skip 2-byte header (version, ttl) + 2-byte sequence
  const fields: Record<string, string | number> = {};

  while (offset + 4 <= buf.length) {
    const tlvType = buf.readUInt16BE(offset);      // big-endian
    const tlvLen  = buf.readUInt16BE(offset + 2);  // big-endian
    offset += 4;

    if (offset + tlvLen > buf.length) break; // malformed / truncated
    const value = buf.subarray(offset, offset + tlvLen);

    switch (tlvType) {
      case 1:  // MAC Address — 6 raw bytes
        fields.macAddress = [...value].map(b => b.toString(16).padStart(2, "0")).join(":");
        break;
      case 5:  fields.identity = value.toString("utf8"); break;
      case 7:  fields.version = value.toString("utf8"); break;
      case 8:  fields.platform = value.toString("utf8"); break;
      case 10: // Uptime — 4 bytes LITTLE-ENDIAN uint32 (the only LE value)
        if (tlvLen === 4) fields.uptime = value.readUInt32LE(0);
        break;
      case 11: fields.softwareId = value.toString("utf8"); break;
      case 12: fields.board = value.toString("utf8"); break;
      case 15: // IPv6 — 16 bytes
        if (tlvLen === 16) fields.ipv6 = formatIpv6(value);
        break;
      case 16: fields.interfaceName = value.toString("utf8"); break;
      case 17: // IPv4 — 4 raw bytes
        if (tlvLen === 4) fields.ipv4 = `${value[0]}.${value[1]}.${value[2]}.${value[3]}`;
        break;
    }
    offset += tlvLen;
  }
  return fields;
}

Reference Implementations

| Language | Source | Notes | |----------|--------|-------| | C | github.com/haakonnessjoen/MAC-Telnet (protocol.c, protocol.h) | Canonical ground truth. TLV enum + ntohs big-endian TLVs + le32toh uptime | | C (dissector) | Wireshark epan/dissectors/packet-mndp.c | Official protocol dissector — confirms type IDs and ENC_BIG_ENDIAN TLVs | | Go | github.com/middelink/mikrotik-fwupdate | Secondary protocol cross-check | | Elixir | hex.pm mndp package | Confirms TLV type IDs | | Swift | Open-source macOS implementations | Confirms raw-byte MAC encoding |

Verified: The TLV type IDs and byte order in this skill were cross-checked against MAC-Telnet's protocol.c and the Wireshark dissector — both agree that TLV type/length are big-endian and that uptime (type 10) is the sole little-endian value.

Related Skills

• For RouterOS CLI/REST basics: see routeros-fundamentals skill
• For the /console/inspect command tree: see routeros-command-tree skill
• For packet capture and TZSP streaming: see routeros-sniffer skill
• For QEMU CHR setup (testing without hardware): see routeros-qemu-chr skill

Related MCP Tools

• For RouterOS docs lookup: use the rosetta MCP server tools (routeros_search, routeros_get_page)